| No. | Brand | F | C | H | E | L | J | d | i |
| 41.63030 | Nachi | - | 5.724 in | 0.198 in | 5.281 in | - | - | - | - |
| 118A-241-AT-0 | Parker | - | 19.5 kN | - | - | 84 mm | 90.5 mm | - | - |
| F621216F | John Deere | - | - | - | - | - | - | - | - |
| A8vo107la1kh2 | - | - | - | - | - | - | - | 90 | - |
| 30% | - | - | - | - | - | - | - | - | - |
| 93310-340N8-00 | - | - | - | - | - | - | - | - | - |
| 10pcs | - | - | 43.55 kN | - | - | - | 176 mm | 55.56 mm | - |
| 2pcs | - | 69.5 mm | - | - | - | - | - | - | - |
| 915X2150 | - | - | - | - | - | - | - | - | - |
| 61816 | SKF | - | - | - | - | - | - | - | - |
| 634 | - | - | - | - | - | - | - | - | - |
| 2065-T | Bower | - | - | - | - | - | - | - | - |
| 6001-2RS | - | - | - | - | - | - | - | - | - |
| SX95 | John Deere | - | - | - | - | - | - | - | - |
| 30% | - | - | 25.7 kN | 102 mm | - | 129 mm | - | - | - |
| 505 | - | - | - | - | - | - | - | 50 | - |
| 030-150 | - | - | - | - | - | - | - | - | - |
| 2pcs | - | - | - | - | - | - | - | 25 mm | - |
| 5204A | Nachi | - | - | - | - | - | - | - | - |
| 6208 | NSK | - | - | - | - | - | - | - | - |
| 2209K | NTN | - | - | - | - | - | - | - | - |
| 34CrMo4 | - | - | - | - | - | - | - | - | - |
| BDZ-155A(ZA-1) | - | - | - | - | - | 86 mm | 64 mm | - | - |
| 17x35x8mm | - | - | - | - | - | - | - | - | - |
| 10000 | - | - | - | - | - | - | - | 60 | - |
| 4x13x5mm | - | - | 12.8 kN | - | - | 94 mm | - | 20 mm | - |
| 1637- | - | - | - | - | - | - | - | - | - |
| JB045XP0 114.3*130.175*7.9375mm Thin Section Ball Bearing Harmonic Drive Wave Generator | N1:24.00 mm; Cage Type:EJ; Shaft Diameter d:65 mm; Seal:VR615; End Cover2:EC518-615; L:345.00 mm; Material :Cast Iron; Locknut:KM15; H:194 mm; A1:100 mm; |
| D28 Thrust Ball Bearing / Axial Deep Groove Ball Bearing 55.563x91.288x20.65mm | Designation of housing:FL206N-; Designation of open end cover:SCOU206-19; N:16mm; s1:15 mm; G:M6x1; A1:13 mm; Dz:70 mm; H:148 mm; Weight:0.89 kg; Recommended tightening torque for set screw:3.7 Nm; |
| CSED055 Thin Section Ball Bearing 139.7x165.1x12.7mm | C:31.85 kN; L:120 mm; Z:70.3 mm; T max.:100 °C; G:M6x1; A:54 mm; s1:20.6 mm; S:10.2 mm; E:22 mm; T min.:-40 °C; |
| 5311ZZ High Speed Double Row Angular Contact Ball Bearings 55*120*49.2mm | E:13 mm; C:12.8 kN; S:12.7 mm; J:52 mm; H1:11 mm; A:40 mm; G:M6x1; s1:15.5 mm; L1:22 mm; H:30.2 mm; |
| KC050AR0 Thin Section Ball Bearing | Fatigue limit load, Cu:3.7 kN; d:180 mm; Maximum Capacity / Filling Slot:No; Snap Ring:No; Inch - Metric:Metric; Outer Race Width:1.299 Inch | 33 Mill; Min operating temperature, Tmin:-60 °C; ra max:2 mm; Minimum Buy Quantity:N/A; Mass:4.76 kg; |
| 5208ZZ Axial Double Row Angular Contact Ball Bearings 40*80*30.2mm | C0:18.2 kN; A:51 mm; d:38.1 mm; B:49.2 mm; J:137.5 mm; s1:24.6 mm; Weight:1.98 kg; Designation of housing:PLE208-; H1:18.5 mm; S:19 mm; |
| BA3 / BA 3 Single Row Thrust Ball Bearing 3x8x3.5mm | C90 - Dynamic Radial Rating (90 million revolutions)5:166000 lbf; C1 - Dynamic Radial Rating (1 million revolutions)6:640000 lbf; C0 - Static Radial Rating:1800000 lbf; Ab - Cage-Cone Frontface Clearance:0.17 in; Ca90 - Dynamic Thrust Rating (90 million revolutions)7:140000 lbf; K - Factor8:1.19; B - Cone Width:4.0000 in; a - Effective Center Location4:5.03 in; d:40.0000 in; Cg - Geometry Factor:0.402; |
| KC120CP0 304.8*323.85*9.525mm Thin Section Ball Bearings Slim Section Bearings | d:8 mm; Dynamic load, C:3.35 kN; Precision Class:ABEC 1 | ISO P0; Nlim (grease):32,000 rpm; Minimum Buy Quantity:N/A; f0:12.5; Outside Diameter:0.866 Inch | 22 Mill; Bore:0.315 Inch | 8 Milli; Long Description:8MM Bore; 22MM Outsi; Inch - Metric:Metric; |
CSEB025 Thin Section Ball Bearing 63.5x79.375x7.938mm Video